SHOW PRICES INCLUDING VAT
Trustpilot
Click to visit the Rapid Blog - Supporting welders every step of the way
0Your Basket : £ 0.00
WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
01CGB10 Protec Metallotion CE15L Anti Spatter Fluid, 10Ltr
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : 01CGB10  Mfr Ref : 01C.GB10

    Protec Metallotion CE15L Anti Spatter Fluid, 10Ltr
    01C.GB10 01CGB10

    £43.65  EX VAT
     Buy in 3 easy interest free payments of £14.55† with

    Bio Anti Spatter Lotion, ready to use, water-based, silicone-free.

    Characteristics:

    • METALLOTION PROTEC CE15L is a non-flammable Anti Spatter Lotion to spray on workpieces and jigs.
    • CE15L takes effect in wet and dry phase.
    • CE15L is also a temporary corrosion protector.
    • CE15L is non-toxic and biodegradable.

    Advantages:

    • METALLOTION PROTEC CE15L is tested and approved for welding, painting, electro-coating, powder-coating, zinc-coating, galvanisation.
    • CE15L is approved for automotive industry, traffic engineering, off-shore technology, container engineering, steel construction, crane industry, no pores arise in the welding seam.
    • CE15L is a protecting and degreasing agent for all kinds of metal surfaces -a subsequent fine cleaning is sufficient.

    Customer Benefits:

    Cost catcher and time saver because post-treatment is being cancelled higher quality by spatter free metal surfaces cost-benefit factor > 100%, pre-treatment for every type of coating technology does not form residues.

    Application:

    The application of Trigger Pump Spray PROTEC HSP 3K or PROTEC ECO-Sprayer guarantees perfect atomisation, optimal wetting and high efficiency. HLVP-Spray Guns or Spray Automat are suitable for series production (e.g. automotive industry).

    Brochures & Manuals

    BROCHURES & MANUALS
       View Brochure

    Related Items

    Anti-Spatter FAQs

    Practical answers on where and how to use anti-spatter products, choosing between types, and getting clean results afterwards.

    Where should I apply anti-spatter?icon-minus-redicon-plus-red

    Apply it to the surfaces you want to keep free of spatter: the workpiece either side of the joint, jigs, clamps and fixtures, and the outside of the torch nozzle or shroud. One maker's data sheet lists workpieces, nozzles, shrouds, jigs and tools as suitable surfaces for its water-based product.

    Keep it away from the contact tip bore and gas ports unless the torch maker says otherwise, as anything that blocks gas flow can cause weld faults. Apply it to cool surfaces before welding starts and let it settle or dry as the label directs.

    Is it safe to spray anti-spatter on a hot torch or near an arc?icon-minus-redicon-plus-red

    Not unless the maker says so. Many aerosol anti-spatter products contain flammable propellants or solvents, so spray them away from arcs, sparks and hot metal, and let the torch cool first. Even non-flammable types are best applied to a cool nozzle so the film lays evenly.

    Use it in a ventilated place, keep aerosols away from heat and sources of ignition, and follow the warnings on the label and safety data sheet. If in any doubt, treat the product as flammable until the data sheet says otherwise.

    How much anti-spatter should I use and how should I spray it?icon-minus-redicon-plus-red

    Less is usually better. Shake an aerosol well, hold it at the distance the label recommends and spray sparingly to give a thin, even film. A thin film works better than a heavy wet coat, which can run, collect dirt and, with some products, affect the weld.

    Spraying distances and drying times differ between products, so follow the instructions for yours. Wipe off any pools. If you see pores or smoke from the weld area, you may be using too much.

    How do I remove spatter that has stuck despite using anti-spatter?icon-minus-redicon-plus-red

    Anti-spatter makes spatter easier to remove but does not stop all of it. TWI notes that spatter can be removed by grinding, which is time-consuming, or quickly with a chipping hammer or spatter chisel without damaging the parent metal. Use eye protection and gloves, as loose spatter can fly off.

    Spatter that sticks hard, or that appears in large amounts, is often a sign of the wrong settings rather than too little spray. Check wire feed speed, voltage, gas flow and the condition of the contact tip before blaming the product.

    See all 6 questions for this category

    Shop Similar Categories